2.4GHz Wireless A/V Sender
User Manual
Fig. 2
1
Receiver/Transmitter
2
Fig. 3
3
3
4
5
4
5
6
6
7
7
Transmitter
Receiver
Setting Up
Before you make the connection:
• Set the channel by pressing the select button on the front of the transmitter
and the receiver to the same channel.
1. Setting up the Transmitter
1.1 Connect the Transmitter to an A/V device
Connect the mini-plug of the provided A/V cables to the A/V jack on the
rear of the transmitter; connect the other end of the cables to the A/V
jacks of the A/V device labeled AUDIO/VIDEO OUT. See Fig. 4.
2
Fig. 4
A/V Cable
OUT
VIDEO
AUDIO
Transmitter
Satellite receiver/DVD/VCD
Note 1: If the A/V equipment has only one output for audio (mono
sound only), connect the white plug to that single audio output jack.
1.2 Power Supply
a. Plug one end of the provided power adaptor into a wall outlet and
the other end into the rear of the transmitter. See Fig. 5.
b. Turn on the transmitter. The LED on the front of the unit should
light up.
Fig. 5
POWER
ON-OFF
Wall Outlet
Transmitter
2. Setting up the Receiver
3
2.1 Connect the Receiver to a TV
A/V Connect – for TV with A/V Input Jacks
Connect the mini-plug of the provided A/V cables to the A/V jack on the
rear of the receiver; connect the other end of the cable to the A/V jacks
on the TV labeled AUDIO/VIDEO IN. See Fig. 6.
Fig. 6
VIDEO AUDIO IN
TV
A/V Cable
Receiver
RF Connection – for TV without A/V Input Jacks
If there is no A/V input jacks on your TV, you will need to get an RF
modulator (available at your local electronics store) to make the
connection between TV and receiver. See Fig. 7.
Receiver
Fig. 7
A/V Cable
CH 3/4
RF OUT
VHF/UHF
VIDEO AUDIO IN
TV
RF Modulator
4
Note 1: Connect the yellow plug to the jack labeled VIDEO, the red plug
to the jack labeled AUDIO RIGHT and the white plug to the jack labeled
AUDIO LEFT.
Note 2: If the TV has only one input for audio (mono sound only),
connect the white plug to that single audio in jack.
2.2 Power Supply
a. Plug one end of the provided power adaptor into a wall outlet and
the other end into the rear of the receiver. See Fig. 8.
b. Turn on the receiver. The LED on the front of the unit should light
up.
Fig. 8
POWER
ON-OFF
Wall Outlet
Receiver
5
Specifications
Transmitter/Receiver
A/V Transmitting Frequency
A/V Signal Range
Antenna
2.4GHz
100 meters (300 feet) clear line of sight
Built-in antenna
Channel
4 selectable channels
Audio
Stereo audio input and output
Composite input and output
12.5 x 8 x 2.5 (cm) for transmitter/receiver
125g for transmitter/receiver
DC6V, 500mA
Video
Dimensions
Weight
Power
Operating Temperature
0℃ ~ 40℃ (32℉ ~ 104℉)
Providing the latest technologies to our customers is our responsibility;
therefore, we reserve the right to change the specifications without prior notice.
Troubleshooting
If you are not getting any signal at all
• Check that the transmitter and receiver are properly connected to the A/V
device from which you want to send/receive the A/V signal.
• Make sure the transmitter and the receiver are turned on.
• Check power switches on the remote TV and video source (VCR, DVD
player, satellite receiver, etc).
• Make sure power plugs are pushed all the way in.
• Check all cable connections.
• Check the CHANNEL switch on both transmitter and receiver are set to the
same number.
• If you connect the receiver to a TV through an RF modulator, check that the
TV is tuned to the same channel as the TV Channel switch on the RF
modulator (3 or 4).
If the signal is poor, or there is interference
• Adjust the transmitter by rotating orientations until you get the best reception.
• Change the channel on both transmitter and receiver and make them the
same.
6
• If there is a microwave oven in use in the path between the transmitter and
receiver, remove the microwave oven or turn it off.
• Make sure the transmitter and receiver are within range of each other (range
of approximately 300 feet; 100 meters in a clear line of sight).
Care and Maintenance
• Keep all its parts and accessories out of the reach of young children.
• Do not attempt to open the case. Non-expert handling of the device may
damage it.
• Keep dry. Precipitation, humidity, and liquids, contain minerals that will
corrode electronic circuits.
• Do not use or store in dusty, dirty areas. Moving parts may be damaged.
• Do not store in hot areas. High temperatures can shorten the life of
electronic devices and warp or melt certain plastics.
• Do not store in very cold areas. When the A/V sender warms up (to its
normal temperature), moisture can form inside the case, which may damage
electronic circuit boards.
• Do not drop, knock, or shake it. Rough handling can break internal circuit
boards.
• Do not use harsh chemicals, cleaning solvents, or strong detergents when
cleaning.
• Operate this product using only the power supply included with it.
• Do not overload electrical outlets or extension cords as this can result in fire
or electric shock.
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
7
|
Radio Shack Range PRO 2018 User Guide
RCA Camcorder EZ4000 series User Guide
Regency Indoor Fireplace F2100M User Guide
RocketFish Conference Phone RF QS2 T User Guide
Samsung Printer ML 2570 Series User Guide
Sanyo Air Conditioner XMS0972 User Guide
Sanyo Vacuum Cleaner SC B550R User Guide
Schumacher Battery Charger 85 716 User Guide
SeaLand Heat Pump Vacuum Pump User Guide
Sega Video Games MAN S075 UK User Guide