RocketFish Speaker System RF RBWS01 User Guide

RF-RBWS01 Wireless Bookshelf Speakers  
Package contents  
Connecting power to the wireless speaker  
Establishing communication  
Connect the AC power adapter to the wireless  
speaker and plug into an AC power outlet. The  
wireless speaker system turns on automatically.  
The wireless sender/receiver and wireless speakers were pre-joined so they will communicate with  
each other right out of the box. So if this is your first Rocketboost enabled product you can skip  
this section and go to the next section, Listening to music.  
AC power adapter  
for wireless speakers  
Rocketboost network notes:  
Every Rocketboost network must contain  
one hub device, which helps devices join  
the network. The network can have only  
one hub, which you can enable using the  
hub switch on the back of all Rocketboost  
wireless sender and wireless  
DC IN  
15V/1.5A  
3.5 mm  
audio cable  
AC power adapter  
for wireless sender/receiver  
If you need to rejoin the wireless sender/receiver to the wireless speakers, and this is your only  
Rocketboost enabled product, then use the following steps.  
1 Set the HUB STATUS switch on the wireless sender/receiver to ENABLE if this is your first  
Rocketboost product set.  
Wireless sender/receiver  
DC IN  
15V/1.5A  
sender/receivers. If this is your first  
Rocketboost product, you should make  
the wireless sender/receiver the hub, if you  
already have Rocketboost products, you  
should disable hub mode on this device.  
Right speaker  
back  
The power indicator turns green when the HUB STATUS switch is set to ENABLE.  
The power indicator turns blue when the HUB STATUS switch is set to DISABLE.  
3.5 mm to RCA adapter  
(6 inches/15.25 cm)  
USB cable  
Remote control  
2 Press and hold on the wireless sender/receiver for more than three seconds to put it into  
joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode  
for 30 seconds.  
3 Press and hold the button on the wireless speaker for more than three seconds  
so the wireless sender/receiver and wireless speaker enter connection mode.  
User Guide  
Quick Setup Guide  
Wireless speakers  
Important: Hub devices must always have  
power for your network to operate. The  
hub device can be in standby (power-  
saving) mode, but must stay plugged in.  
Connecting audio source and power to wireless sender/receiver  
1 Connect your audio source to the LINE IN jack or USB jack on the rear of the wireless sender,  
using the 3.5 mm audio cable or the USB cable. If necessary, you can also use the 3.5 mm to RCA  
adapter, if your audio device uses RCA-type line out connectors.  
Initial setup  
1
2
Unpack the package contents  
The power indicator lights steadily if the joining was successful.  
The power indicator blinks slowly if the joining was not successful.  
Adjust the antennas  
Included 3.5 mm cable  
and 3.5 mm to RCA adapter  
Adjust the antennas to gain the best audio signals.  
Tip: In some cases, you may improve range by rotating  
both antennas 0° to create a 180° angle.  
Included 3.5 mm cable  
To audio output jack  
4 After the link is established, if the Source indicator on  
the wireless speaker is still not illuminated, make sure  
that your source is turned on.  
OR  
To audio  
output jack  
Lights when  
speaker is  
receiving  
audio from  
sender  
standby  
For more instructions, see your User Guide.  
3
4
Enable the remote control battery  
Remove the tab from the bottom of  
the remote control.  
SOURCE  
If you already have other Rocketboost devices you need  
to join both the wireless sender/receiver and the wireless  
speaker to your existing hub device. See the User Guide  
for detailed instructions on how to do this.  
Included USB cable  
Set up the wireless sender/receiver  
and wireless speaker  
To USB jack  
Listening to music  
The Quick Setup Guide will show you a typical  
setup using an audio device (such as an MP3  
player, PC or A/V receiver). For more information  
about how to use other Rocketboost products  
with this product, see your User Guide.  
See the following steps for further setup details.  
2 Remember to turn the volume up on your audio source especially if connected to a headphone  
1 Turn on the wireless sender/receiver and wireless speaker. The power indicator LEDs should  
light steadily. If they are blinking you need to rejoin the wireless sender/receiver and wireless  
speaker. See the Establishing communication section above.  
output.  
3 Connect the AC power adapter to the wireless USB sender/receiver and plug into an AC power  
outlet.  
2 Point the remote control at the wireless sender/receiver and select either USB-In or LINE-In  
depending on which audio input you are using.  
RF-RBUSB  
Wireless  
sender/receiver  
RF-RBWS01  
Wireless  
speakers  
The wireless sender/receiver automatically turns on and the power indicator turns green.  
3 Play music from the audio device connected to your wireless sender/receiver and listen to it  
from the wireless speakers.  
4 Adjust the volume level on your wireless speaker. If you have multiple audio sources in your  
Rocketboost network, press the Source button on the wireless speaker to hear the next audio  
source. Press the Source button again to cycle through all available audio sources.  
Note: Be sure to turn up the volume on your audio source device, especially if you are  
connected to a headphone output.  
© 2011 BBY Solutions, Inc. All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA 55423-3645  
ENGLISH 11-0203  
QUICK SETUP GUIDE  
 

QVS Surge Protector PP114C User Guide
Radio Shack Radar Detector 22 1697 User Guide
RCA MP3 Player M250 User Guide
RCA Satellite TV System Satellite TV Antenna User Guide
Rotel Car Stereo System RD 550 User Guide
Rotel Turntable RP 900 User Guide
Samsung Digital Camera A55W User Guide
Samsung Portable Speaker DAF60 User Guide
Samsung Refrigerator SR S25 User Guide
Sealife Digital Camera DC300 DC310 User Guide