GAS COOKER
INSTRUCTION MANUAL
Model number: RHGC1
Please read these instructions carefully and
keep them for future reference
For Customer Services, Spare Parts & Warranty Information
please call 0845 683 8717
Opening times: Monday - Friday
8am until 8pm
Saturday & Sunday 10am until 4pm
CONTENTS:
1. BRIEF PRESENTATION OF PRODUCT
2. WARNINGS
3. INSTALLATION AND PREPARATIONS FOR USE
3.1 Environment where the appliance is to be installed
3.2 Installation of product
3.3 Adjustment of feet
3.4 Gas connection
3.5 Electric connection and safety
3.6 Gas conversion
4. USE OF YOUR PRODUCT
4.1 Use of gas burners
4.1.1 Control of hob burners
4.1.2 Control of oven burner
4.1.3 Control of grill burner
4.1.4 Use of mechanical minute minder
4.2 Accessories used in oven
5. CLEANING AND MAINTENANCE
5.1 Cleaning
5.2 Maintenance
6. SERVICE AND TRANSPORT
6.1 Basic troubleshooting before contacting service
6.2 Information related to the transport
Gas Cooker
RHGC1
FREE-STANDING COOKERS
SPECIFICATION SHEET
Nominal Dimensions
Height (Adjustable Feet max. +3.5cm)
cm
cm
cm
90
50
60
Width
Depth
Hob Features
Hob
Enamel
3000
Rapid Gas Burner Ø10cm
Semi-rapid Gas Burner Ø7.5cm
Auxiliary Gas Burner Ø5.5cm
Burner Safety Valves
Button Ignition
W
W
W
1750
1000
Yes
Yes
Enamel Pan Supports
Gas Conversion Kit
Standard
Standard
Oven Features
Oven Type
Gas
Oven Volume (without fan)
lt
52.5
Cavity Dimensions (without fan)
mm
370 x 330 x 430
Oven Light (25W)
Yes
Standard
Yes
Easy to Clean Enamel
Thermostat
Oven Safety
Standard
2800
2200
Yes
Oven Burner (Thermostat Controlled)
Gas Grill
W
W
Minute Minder
Roasting Tray (Deep Tray)
Chromed Grid with Stoper
Grill Pan with Handle Set
1
1
Yes
Full outer glass and Inner metal door (small glass) Oven Door
Standard
Others
Total Power (Depends on Model) Maximum
Voltage
kW
V
10,1
230
Energy consumption according to the EN50304 Standards
(Depends on Model)
kWh
-
RoHS Compliance
CE Compliance
Standard
Standard
106
Depth with Door Open
cm
1. BRIEF PRESENTATION OF PRODUCT
9
8
7
1
2
6
10
11
14
12
4
3
13
5
List of Components:
1- Cooker top
9- Oven Lamp
10- Semi-Rapid Burner
11- Rapid Burner
12- Auxillary Burner
13- Pan Support
14- Semi-Rapid Burner
2- Control Panel
3- Oven Door Handle
4- Adjustable Feet
5- Oven Door
6- Oven Tray
7- Wire Grid
8- Grill Pan and Handle Set
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
1
2. WARNINGS
General Safety
•
These warnings are provided in the interest of your safety. Read this manual
carefully before using the appliance.
•
•
This appliance has been designed for non-professional, domestic use only.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
•
•
Your appliance is produced in accordance with the local and international
standards and regulations applicable.
The maintenance and repair works must be made only by authorised service
technicians. The installation and repair works without following proper
knowledge may endanger you.
•
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
•
•
Do not try to lift or move the appliance by pulling the door handle.
It is dangerous to alter or modify the specifications of the appliance in any way.
Installation
•
The appliance must be installed by a qualified professional according to the
instructions provided. The producer is not responsible for any damage that
might be caused by defective placement and installation by unauthorised
people.
•
When you unpack the appliance, make sure that it is not damaged during
transportation. In case of any defect; do not use the appliance and contact to
the authorised maintenance service immediately. As the materials used for
package (nylon, stapler, strafoam...etc) may cause harmful effects to children,
they should be collected and removed immediately.
For authorised people;
•
Compare the features of the electricity network with the technical information
on the rating label before plugging the appliance in.
•
Prior to installation, ensure that the local distribution conditions (nature of the
gas and gas pressure) and the adjustment of the appliance are compatible.
The adjustment conditions for this appliance are stated on the label.
•
This appliance is not connected to a combustion products evacuation device. It
shall be installed and connected in accordance with current installation
regulations. Particular attention shall be given to the relevant requirements
regarding ventilation.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
2
During Use
•
When you first run your oven a certain smell will be emanated arising from the
insulation materials and the heater elements. For this reason, before using
your oven, run it empty at maximum temperature for 45 minutes. At the same
time you need to properly ventilate the environment in which the product is
installed.
•
While your appliance operates, its outside surfaces heat up. The interior
surfaces of oven and the flue outlet are quite hot. Even if the appliance is
turned off, these parts keep its heat for a specific time. Do not touch onto hot
surfaces and keep children away.
•
•
Always use oven gloves to remove and replace food in the oven.
Always stand back from the appliance when opening the oven door to allow
any build up of steam or heat to release.
•
Do not leave the cooker while cooking with solid or liquid oils. They may catch
fire on condition of extreme heating. Never pour water to the flames that are
caused by oil. Cover the saucepan or frypan with its cover in order to choke the
flame that has occured in this case and turn the cooker off.
•
The use of a gas cooking appliance results in the production of heat and
moisture in the room in which it is installed. Ensure that the kitchen is well
ventilated: keep natural ventilation holes open or install a mechanical
ventilation device (mechanical extractor hood). Prolonged intensive use of the
appliance may call for additional ventilation, for example opening of a window
or more effective ventilation, for example increasing the level of mechanical
ventilation where present.
•
•
While using the grill burner, keep the oven door open and always use the grill
deflector shield supplied with the product. Never use the grill burner with the
oven door closed.
If you will not use the appliance for a long time, plug it off. Keep the main
control switch off. Also when you do not use the appliance, keep the gas valve
off.
•
•
•
When the door of oven is open, do not leave anything on it. You may
unbalance your appliance.
Protect your appliance against atmospheric effects. Do not leave it to effects
such as sun, rain, snow, powder etc.
Do not keep flammable materials close while the appliance is operating.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
3
•
•
Pay attention to the cables of the other electrical devices operating near the
appliance, so as not to touch to hot points.
The appliance is not intended to be operated by means of an external timer or
separate remote control system.
•
•
Do not hang towels, dishcloths or clothes from the appliance or its handles.
Pay attention to the expressions that have figures, while you are reading the
operating manual.
Safety when Cleaning and Maintenance
•
•
•
Turn the appliance off before the operations such as cleaning or maintenance.
You can do it after plugging the appliance off or turning the main switches off.
!
WARNING: Ensure that the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven
door glass since they can scratch the surface, which may result in shattering of
the glass.
•
Every care is taken to ensure the safety of the customer. Glass can break, be
carefull when cleaning the glass as not to scratch it. Do not knock or hit the
glass with the accessories.
Children Safety
!
•
CAUTION: Accesible parts may be hot when the grill is in use. Young
children should be kept away. Keep children away from the oven.
•
•
While the front door is open, do not let children climb on the door or sit on it.
Children should be supervised to ensure that they do not play with the
appliance.
FOR EFFICIENCY AND SAFETY OF APPLIANCE, WE RECOMMEND YOU
ALWAYS TO USE THE ORIGINAL SPARE PARTS AND TO CALL ONLY OUR
AUTHORISED SERVICES.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
4
3. INSTALLATION AND PREPARATIONS FOR USE
● Before operating your new appliance please read this instruction manual
carefully. It contains important information concerning the safe installation and
operation of the appliance.
● Please keep these operating instructions for future reference. Make sure that
the instructions are kept with the appliance if it is sold, given away or moved.
● Gas cookers must be disconnected and installed by a Gas Safe register
engineer. This scheme has replaced the Corgi registration scheme. For details
●The appliance must be installed by a qualified professional according to the
instructions provided.
●Any necessary adjustments or maintenance must be performed after the cooker
has been disconnected form the electricity supply.
●The producer is not responsible for any damage that might be caused by
defective placement and installation by an unauthorised person.
3.1 Environment where your appliance will be installed
! This unit may be installed and used only in permanently ventilated rooms
according to the British Standards Codes Of Practice: B.S. 6172/B.S. 5440, Par. 2
and B.S. 6891 Current Editions. The following requirements must be observed:
●The cooker should not be installed in a bed sitting room with a volume of less
than 20m³. If it is installed in a room of volume less than 5m³ an air vent of
effective area of 110cm² is required, if it is installed in a room of volume between
5m³ and 10m³ a supplementary airvent area of 50cm² is required, if the volume
exceeds 11m³ no airvent is required. However, if the room has a door or a window
which opens directly to the outside no air vent is required even when the volume is
between 5m³ and 11m³.
● During prolonged use of the appliance you may consider it necessary to open a
window to the outside to improve ventilation.
● If there are other fuel burning appliances in the same room, B.S.5440 Part 2
Current Edition, should, be consulted to determine the requisite air vent
requirements.
Emptying of the Burned Gases from Environment
The cooking appliances that operate with gas, throw the burned gas wastes out
directly to the outside or through the cooker hoods that are connected to the a
chimney that opens directly to the outside. If it seems that it is not possible to
install a cooker hood, it is required to set an electric fan on the window or wall that
has access to fresh air. This electric fan must have the capacity to change the air
of the kitchen environment 4-5 times of its own volume of air per hour.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
5
The appliance can be installed next to furniture units which are no taller than the
top of the cooker hob. The wall in direct contact with the back panel of the cooker
must be made of non-flammable material. During operation the back panel of the
cooker could reach a temperature of 50°C above room temperature. For proper
installation of the cooker, the following precautions must be taken:
●The appliance can be placed in a kitchen, dining room or bedsit, but not in a
bathroom.
●All furniture around the appliance must be placed at least 200mm from the top
of the cooker, should the surface of the appliance be higher than the worktop of
this furniture. Curtains should not be placed behind the cooker or less than
200mm away from the sides of the appliance.
●Any hoods must be installed according to the requirements in the installation
manual for the hoods themselves.
● If the cooker in installed beneath a wall cabinet, the latter must be situated at a
minimum of 420mm above the hob. The minimum distance between the worktop
and kitchen units made of combustible material is 700mm (Fig.5).
●The wall in direct contact with the back panel of the cooker must be made of
non-flammable materials.
● Pay attention not to place the cooker near the refrigerator, there must be no
flammable or inflammable materials such as curtain, waterproof cloth, etc. that will
begin to burn quickly.
● It is required that there must be least a 2cm blank space around the product for
air circulation.
●The furniture close to product must be manufactured resistant to temperatures
up to 80°C.
● If the kitchen furniture are higher than the cooktop, it must be at least 10cm
away from the cooker's side.
Min. 60cm
COOKER HOOD
Figure 5
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
6
3.3 Adjustment of feet
Your product stands on 4 adjustable feet. When
the product is placed where it is to be used, check
if the product is balanced. If it is not balanced, you
can make the adjustment by turning the feet
clockwise if required. It is possible to raise the
appliance maximum 35mm by the feet. If the feet
are adjusted do not move the appliance by
dragging, it should be moved by lifting it up.
Figure 6
3.4 Gas connection
Assembly of gas supply and leakage check
The cooker should be connected to the gas-supply by a gas safe registered
installer. During installation of this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the convenience of any subsequent
removal or servicing. Connection of the appliance to the gas mains or liquid gas
must be carried out according to the prescribed regulation in force, and only after it
is ascertained that it is adaptable to the type of gas to be used. You can find the
information related to appropriate gas types and appropriate gas injectors on
technical data table. If the pressure of used gas is different than these values
stated or not stable in your area, it may be required to assemble an available
pressure regulator on the gas inlet. It is certainly required to contact to the
authorised service to make these adjusments.
Thepointsthatmust bechecked duringflexiblehoseassembly
Connecting the gas supply
To make the connection, a flexible hose should be used corresponding to the
current gas regulations which are:
● the hose must never be at any point in its length in contact with the 'hot' parts of
the cooker;
● the hose must never be longer than 1.5 metre;
● the hose must not be subject to any tension or torsional stress and it must not
have any excessively narrow curves or bottlenecks;
● the hose must be easy to inspect along its entire length to check its condition;
● the hose must always be in good condition, never attempt to repair.
! The installation must comply with gas safety (installation and use) regulations
1984. In all cases for the above, by law, a qualified, corgi approved engineer must
be called for installation.
As gas is turned on, all connection parts and hose must be checked with soapy
water or leakage fluids. Do not use naked flame to check gas leakage. All metal
components used during gas connection must be clear of rust. Also check the
expiry dates of components to be used.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
7
Thepointsthatmust bechecked duringfixedgas connectionassembly
During connections always keep the nut on the gas manifold fixed, while rotating the
counter-part. Use spanners of appropriate size for safe connection. For all surfaces
between different components, always use the seals provided in the gas conversion
kit. The seals used during connection should also be approved to be used in gas
connections. Do not use plumbing seals forgas connections.
Remember that this appliance is ready to be connected to gas supply in the UK. If you
need to use it in another country, any of the connections in the figure below can be
required. In such a case, learn the appropriate connection parts and obtain those
parts toperform a safe connection.
Figure 7
!
ATTENTION! DO NOT use any match or lighter for control of gas
leakage.
3.5. Electrical connection (UK ONLY)
For your safety please read the following information.
WARNING: This appliance must be earthed.
•
•
•
The appliance must be connected to a 230-240 volts 50 Hz AC supply by
means of a three pin socket, suitably earthed and should be protected by a 3
amp fuse in the plug.
The appliance is supplied with a 13-amp 3-pin mains plug fitted with a 3 amp
fuse. Should the fuse require replacement, it must be replaced with a fuse rated
at 3 amp and approved to BS1362.
The plug contains a removable fuse cover that must be refitted when the fuse
is replaced. In the event of the fuse cover being lost or damaged, the plug must
not be used until a replacement cover has been obtained. If the mains plug is
unsuitable for the socket outlet in your home or is removed for any other
reason, then the fuse should be removed and the cut off plug disposed of safely
to prevent the hazard of electric shock.
•
There is a danger of electric shock if the cut off plug is inserted into any 13
amp socket outlet.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
8
IMPORTANT: How to wire a 13 amp plug
The wires in the mains lead on this
appliance are coloured in accordance with
the following code:
•
•
•
Green and Yellow – Earth
Blue – Neutral
Earth
(Green-Yellow)
Fuse (3 Amp)
Live (Brown)
Neutral (Blue)
Brown – Live
Cord Clamp
Figure 8
As the colours may not correspond with the markings identifying the terminals in
your plug proceed as follows. The green and yellow wire must be connected to the
terminal in the plug, which is marked with the letter E, or with the earth symbol or
coloured green and yellow. The blue wire must be connected to the terminal
marked N. The brown wire must be connected to the terminal marked L.
3.6 Gas conversion
Caution : The following procedures must be undertaken by authorised
service people.
Your appliance is adjusted to be operated with LPG/NG gas. The gas burners can
be adapted to different types of gas, by replacing the corresponding injectors and
adjusting minimum flame length suitable to the gas in use. For this purpose,
following steps should be performed:
Changing injectors:
Hob Burners:
•
•
•
•
Cut off the main gas supply and unplug from the electric mains.
Remove the burner cap and the adapter(Figure 9).
Unscrew the injectors. For this, use a 7mm spanner(Figure 10).
Replace the injector with the ones from the gas conversion kit, with
corresponding diameters suitable to the type of gas that is going to be used,
according to the information chart (which is also supplied in the gas conversion
kit).
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
9
Spanner
Injector
Figure 10
Figure 9
Oven/Grill Injectors:
The oven and grill injectors are assembled by a single screw that is placed on the
tip of the burner. For grill burners, this screw is already visible(Figure 11). Remove
the screw, pull the grill burner to yourself and you will see the injector revealed on
the rear surface of the oven cavity (Figure 12).
For oven burners, open the drawer compartment and you will see the assembly screw
below the burner (Figure 13). Remove the screw, move the burner diagonally and the
injector will be revealed on the rear side ofthe burner box (Figure 12).
Remove the injectors with a 7mm spanner and replace the injector with the ones
from the spare set, with corresponding diameters suitable to the type of gas that is
going to be used, according to the information chart (which is also supplied in the
gas conversion kit).
Screw
Screw
Injector
Figure 11
Figure 13
Figure 12
Adjusting the reduced flame position:
The flame length in the minimum position is adjusted with a flat screw located on
the valve. For valves with flame failure device, the screw is located on the side of
the valve spindle(Figure 14). For valves without flame failure device, the screw is
located inside the valve spindle(Figure 15). For easier reduced flame adjustment,
it is advised to remove the control panel (and microswitch, if present) during
adjustment.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
10
To determine the minimum position, ignite the burners and leave them on in
minimum position. Remove the with the help of a small screwdriver fasten or
loosen the bypass screw around 90 angular degrees. When the flame has a
length of at least 4mm, the gas is well distributed. Make sure that the flame does
not die out when passing from the maximum position to the minimum position.
Create an artificial wind with your hand toward the flame to see if the flames are
stable.
Valve with flame failure device
Bypass Screw
Figure 14
For oven burner, operate the oven burner at minimum position for 5 minutes, then
open and close the oven door for 2-3 times to check the flame stability of the
burner.
Reduced flame position adjustment is not required for grill burners.
The position the bypass screw must be loosened for conversion from LPG to NG.
For conversion from NG to LPG, the same screw must be fastened. Make sure
that the appliance is unpluged from the electric mains and the gas supply is open.
Thermostatic oven valve
Bypass Screw
Figure 15
Changing the gas inlet:
For some countries, the gas inlet type can be different for NG/LPG gases. In such
a case, remove the current connection components and nuts (if any) and connect
the new gas supply accordingly. In all conditions, all components used in gas
connections should be approved by local and/or international authorities. In all gas
connections, refer to the “Assembly of gas supply and leakage check” clause
explained before.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
11
4. USE OF YOUR PRODUCT
4.1 Use of gas burners
Ignition of the burners
To determine which knob controls which burner, check the position symbol above
the knob.
•
Manual Ignition of the Gas Burners
If your appliance is not equipped with any ignition aid or in case there is a failure
in the electric network, follow the procedures listed below:
For Hob Burners: To ignite one of the burners, press and turn its knob counter-
clockwise so that the knob is in maximum position, then press the ignition button
immediately, because if you wait there will be a build up of gas and this may cause
the flame to spread. If the flame does not ignite continue to press the ignition
button until you see a stable flame on the burner.
For Oven Burner: To ignite the oven burner, press and turn the oven/grill control
knob counter-clockwise so that the knob is in maximum position, then press the
ignition button immediately, because if you wait there will be a build up of gas and this
may cause the flame to spread. If the flame does not ignite continue to press the
ignition button until you see a stable flame.
For Grill Burner: To ignite the grill burner, turn the oven/grill knob in the clockwise
position until the marker on the knob points at the grill sign
. Then, keep the knob
pressed and press the ignition button immediately, because if you wait there will be a
build up of gas and this may cause the flame to spread. If the flame does not ignite
continue topress the ignition button until you see a stable flame.
•
Electrical Ignition
Ignition by Spark Button: Press the valve of the burner you
want to operate and turn the valve in the counter-clockwise
direction so that the knob is in maximum position and with
your other hand, press the ignition button (Figure 18) at the
same time. Press the ignition button immediately, because if
you wait, a build up of gas may cause the flame to spread.
Continue pressing the ignition button until you see a stable
flame on the burner.
Figure 16
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
12
Flame safety device:
Hob Burners
This hob is equipped with flame failure device provide security in case of
accidentally extinguished flame. If such a case occurs, the device will block the
burners gas lines and will avoid any accumulation
of unburned gas. Wait 90 seconds before re-igniting an extinguished gas burner.
Oven / Grill Burners
Regardless of the model of your appliance, all oven burners are equipped with a
gas safety device. For this reason, during ignition, keep the oven knob pressed
until you see stable flames. If the flames are cut out after you release the knob,
repeat the procedure again. If the oven burner does not ignite after you keep the
burner knob pressed for 30 seconds, open the oven door and do not attempt re-
ignition for at least 90 seconds. When oven flames go out accidentally, repeat the
same procedure.
4.1.1 Control of the hob burners
OFF position
MAX. position
MIN. position
Modulated
Figure 17
The knob has 3 positions: Off (0), maximum (big flame symbol) and minimum
(small flame symbol). After you ignite the burner in maximum position; you can
adjust the flame length between maximum and min. positions. Do not operate the
burners when the knob position is between maximum and off positions.
After the ignition, check the flames visually. If you
see yellow tip, lifted or unstable flames; turn the
Cap
gas flow off, and check the assembly of burner
caps and crowns (Figure 20). Also, make sure that
no liquid has flown into the burner cups. If the
Crown
burner flame goes out accidentally, turn the burner
off, ventilate the kitchen with fresh air, and do not
attempt re-ignition for 90 sec.
Spark
Plug
Burner
Cup
When turning the hob off, turn the knob in the
clockwise direction so that the knob shows "0"
position or the marker on the knob points upwards.
Figure 18
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
13
Your hob has burners of different diameters. The most economic way of using gas
is to choose the correct size gas burners for your cooking pan size and to bring
the flame to minimum position once the boiling point is reached. It is
recommended to always cover your cooking pan.
In order to obtain maximum performance from the main burners, use pots with the
following flat bottom diameters. Using smaller pots than the minimum dimensions
stated below will cause energy loss.
Rapid / Wok Burner: 22-26cm
Semi-rapid Burner: 14-22cm
Auxiliary Burner: 12-18cm
Make sure that the tips of the flames do not spread out of the outer circumference
of the pan, as this may also harm the plastic accessories around the pan (handles
etc.).
Figure 19
When the burners are not in use for prolonged periods, always turn the main gas
control valve off.
!
WARNING:
● Use only flat pans with a sufficiently thick base.
● Ensure that the base of the pan is dry before placing it on the burners.
●The temperature of accessible parts may be high when the appliance is
operating. So it is imperative to keep children and animals out of the reach of the
burners during and after cooking.
●After use, the hob remains very hot for a prolonged period of time, do not touch
it and do not place any object on top of the hob.
● Never place knives, forks, spoons and lids on the hob as they will get hot and
could cause serious burns.
4.1.2 Control of the Oven Burner
After you ignite the oven burner as explained before, you can adjust the
temperature inside the oven as you require, using the numbers on the control
panel or knob ring: Bigger numbers mean higher temperatures, while smaller
numbers mean lower temperatures. For gas mark temperature conversions,
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
14
please reter to the temperature table below for the temperature references of
those numbers. Do not operate the appliance between "Off" position and first
temperature marker in the counter-clockwise direction. Always use the oven
between maximum and minimum numbers. When turning the oven off, turn the
knob in the clockwise direction so that the knob shows "0" position.
RHGC1
TEMPERATURE
2700C
POSITION
MAX.
2500C
•
2400C
5
2200C
•
2000C
1900C
3
•
1800C
1
1600C
MIN.
Preheating
When you need to preheat the oven, we recommend you do so for 10 minutes.
For recipes needing high temperatures, e.g. bread, pastries, scones, soufflés
etc., best results are achieved if the oven is preheated first. For best results when
cooking frozen or cooked chilled ready meals always preheat the oven first.
Cooking
•
•
•
Ensure that food is placed centrally on the shelf and there is sufficient room
around the baking tray/dish to allow for maximum circulation.
Stand dishes on a suitably sized baking tray on the shelf to prevent spillage
onto the oven base and to help reduce cleaning.
The material and finish of the baking tray and dishes used affect base
browning. Enamel ware, dark, heavy or non-stick utensils increase base
browning. Shiny aluminum or polished steel trays reflect the heat away and
give less base browning.
•
•
When cooking more than one dish in the oven, place dishes centrally on
different shelves rather than cluster several dishes on one shelf, this will allow
the heat to circulate freely for the best cooking results.
If you are cooking more than one tray of similar items, for example cakes or
biscuits, swap the trays during cooking or you can remove the top tray when
the food is cooked and move the lower tray to the higher shelf to finish
cooking.
•
Do not place baking trays directly on the oven base as it interferes with the
oven air circulation and can lead to base burning; use the lower shelf position.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
15
4.1.3 Control of the grill burner
!
CAUTION: Accessible parts may be hot when the grill is in use. Young
children should be kept away.
Right after you ignite the burner, place the grill heat deflector under the control
panel. After that, lift the oven door up slowly until it stops at the semi-open (30 °)
position and touches the heat shield.
Assembling the heat deflector
Hold the heat deflector as the warnings face upwards. There are two small slots
on the right and left side of the rear edge of the shield, as shown in the below
Figure 20
There are two screw equipped with bushes under the oven control panel. Align the
bushes with the assembly slots so that the shield is stuck between the control
panel and the bush. Push the shield towards the appliance until it is firmly in its
place.
Cooking
• The grill cooker burner is select by turning the oven/grill knob to the grill
sign . Note that the heat/temperature of the grill is/will be constant and
cannot be adjusted, if you wish to grill items slowly or slower then
increase the distance the food is from the grill burner by placing the grill
pan on a lower shelf. When turning the grill burner off, turn the knob back
to the "0" position.
• Place the tray on the shelf below the grid in order to collect the fat during grilling.
• Place the wire grid on the topmost shelves; 5th or 6th; provided that the food
does not touch the grill burner.
• Preheat the grill on a full setting for a few minutes before sealing steaks or
toasting. The food should be turned over during cooking as required.
• Food should be thoroughly dried before grilling to minimize splashing. Brush
lean meats and fish lightly with a little oil or melted butter to keep them moist
during cooking.
• Foods should be placed on the center of the grid to allow maximum circulation of
air.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
16
•
•
Never cover the grill pan or grid with foil as this can lead to grill fires.
If your appliance has a grill pan and handle set as an accessory, refer to
accessories section for its usage.
!
WARNING: Ensure that the grill is turned off before closing the door.
4.1.4. Use of mechanical minute minder
Set the desired cooking time by turning timer button
clockwise. At the end of this time period, it will make
a bell sound, but the oven continues working. In
order to turn the oven off, you must switch off the
oven kontrol.
Figure 21
4.2 Accessories used in oven
•
The product is already supplied with certain accessories. You can also use
accessories you purchase from the market, but they must be heat and flame
resistant. You can use glass dishes, cake molds, special oven trays that are
appropriate for use in oven. Pay attention to the using instructions by the
manufacturer of those acessories.
•
•
In case small size dishes are used, place the dish onto the wire grid, so it is
completely on the middle part of the grid.
During grilling or cooking the form at the oven tray the can change because of
the high heat that occur during cooking or roasting. The tray will return to its old
form only when the tray cool down after cooking. This is a normal physical
event that occurs during heat transfer.
•
Do not leave glass trays or dishes in cold environment right away after cooking
in the glass tray or dish or put them onto cold and wet surfaces. Place on a dry
kitchen cloth or dish cross, ensure it to cool slowly, otherwise the glass tray or
dish may be broken.
•
•
If you grill in your oven; we recommend that you use the grid that was given in
tray together with product.
As explained in the corresponding clauses, never attempt to use the gas
operated grill burner without the grill protection lid. If your oven has a gas
operated grill burner, but the grill heat shield is missing, or if it is damaged and
cannot be used, request a spare part from the service company (detailed
below, as well as on the front rear cover at the instruction manual).
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
17
Oven Cavity
Rack positions for molded racks
6. Rack
5. Rack
4. Rack
3. Rack
2. Rack
1. Rack
Oven Accessories
* The accessories of your oven may be different due to the model of your product.
Wire grid
Wire grid is used to grill or to place different cookwares on it.
To locate the wire grid correctly in the cavity, put it to any rack and
push it up to the end.
Oven Tray
Oven tray is used to cook stews, chips, etc.
To locate the tray correctly in the cavity, put it to any rack and
push it up to the end.
Grill Pan and Handle Set
Grill pan set is used to grill bread, bacon, sausages, steaks, etc.
WARNING: The grill pan has a detachable handle. Ensure when
using the grill pan handle that it is centralised and securedas seen
in the picture. Do not leave the handle in position when grilling.
Heat Deflector
The heat deflector is used to deflect the heat away from the control
panel. The heat deflector should be fitted before using the grill.
WARNING: The heat deflector may get very hot during use so avoid
touching it until the oven or grill have cooled down. Be careful that
small children do not touch the deflector or other elements when
the oven is in use.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
18
5. CLEANING AND MAINTENANCE
5.1 Cleaning
Be sure that all control switches are off, your appliance cooled and the appliance
is unplugged before cleaning your oven. Check whether the cleaning materials
are appropriate and recommended by the manufacturer before using the cleaning
materials on your oven. As they may damage the surfaces, do not use caustic
creams, abrasive cleaning powders, thick wire wool or hard tools. In case the
liquids that overflow around your oven burn the enameled parts may be damaged.
Immediately clean the overflown liquids.
Cleaning of oven
Wipe the oven with a soft cloth that had been soaked in soapy water after each
use. Later wipe it with a wet cloth once more and then dry it. It may be required to
use a liquid cleaning material from time to time and make a complete cleaning. Do
not clean with dry/powder cleaners or steam cleaners.
Removal of oven door
To remove the oven door;
•
•
Open the oven door(1).
Open the saddle bracket up to end
position(2).
1
•
Close the door till it almost reaches to
the full closed position as shown in 3rd
figure and remove the door by pulling it
towards yourself.
Saddle
bracket
Recessed
form
NOTE: To re-assemble the door follow the
opposite rules of removal.
2
!
Please pay attention that the
recessed forms should be positioned
properly on the hinge counterparts as
nd
shown on 2 figure.
3
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
19
Cleaning of Gas Cooker - Hob Part
• Ensure all switches are off, your appliance cooled and the appliance is
unplugged before cleaning.
•
•
•
Lift up the pan supports, caps and crowns of hob burners.
Wipe and clean the back panel with a soapy cloth.
Wash the caps and crowns of hob burners and rinse them. Do not leave them
wet, immediately dry them with paper cloth.
•
•
After cleaning, make sure that you re-assemble the parts correctly.
Do not clean any part of the hob with metal sponge. It causes the surface be
scratched.
•
The pan support top surfaces may be scratched in time due to usage. These
parts will not get rusted and it is not a production fault.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
20
Burner Caps:
Periodically, enameled pan support, enameled covers, burner heads must be
washed with soapy warm water rinsed and dried. After drying them thoroughly,
replace them correctly.
Enamelled Parts:
In order to keep them as new, it is necessary to clean them frequently with mild
warm soapy water and then dry with cloth. Do not wash them while hot and
never use abrasive powders or abrasive cleaning materials. Do not leave vinegar,
coffee, milk, salt, water, lemon, or tomato juice to remain in contact with
enameled parts for long periods of time.
Stainless Steel:
Stainless steel parts must be cleaned frequently with mildly warm soapy water
and a soft sponge and then dry with a soft cloth. Do not use abrasive powders or
abrasive cleaning metarials. Do not leave vinegar, coffee, milk, salt, water, lemon
or tomato juice to remain in contact with stainless steel parts long periods of time.
5.2 Maintenance
Change of Oven Lamp
First unplug the product off from the electric supply and make sure that the
product is cool. Remove the bulb after removing the glass lens. Assemble the
new bulb resistant to 300°C to replace the bulb that you removed (230 V, 25 Watt,
Type E14). Replace the glass lens. Your product will be ready for use after this
process.
The lamp design is specific for the use in household cooking appliances and it is
not suitable for household room illumination.
Other Controls
Periodically check the gas connection pipe. Even if any simple abnormality is felt,
inform the technical service to have it changed. We recommend the gas
connection parts to be changed once a year. If any abnormality is felt while
operating the control knobs of cooker, contact to the authorized service.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
21
6. SERVICE AND TRANSPORT
6.1 Basic troubleshooting before contacting service
If the oven does not operate :
•
•
The oven may be unplugged or switched off at the plug.
There has been cut off at power and the fuse box/switch needs to checked.
If the oven does not heat :
The heat may be not adjusted with oven's heater control switch.
If the interior lighting lamp does not light :
A replacement bulb is needed.
Cooking (If lower-upper part does not cook equally):
•
•
•
Check the shelf locations, cooking period and heat values according to the
manual.
The hob burners do not operate correctly :
•
•
Check if the burner parts are correctly assembled(especially after cleaning).
The gas supply pressure may be too low/high. For appliances working with
bottled LPG, the LPG cylinder may be depleted.
If you still have any problem with your product, please call to the Service
Company (details at the bottom of the page as well as the front and rear
cover).
6.2 Information related to transport
If you need any transport; keep the original case of product and carry it with its
original case. Follow the transport signs on packaging, tape the cooker on upper
parts, caps and crowns and pan supports to the cooking panels. Place paper
between the upper cover and cooking panel, then tape it to the side surfaces of
oven. Tape cardboard or paper onto the front cover on interior glass of oven as it
will be suitable to the trays, for the wire grid in your oven not to damage to the
oven door during transport. Also tape the oven door to the side panels.
If you do not have the original packaging; prepeare a carriage box so that the
appliance, especially external surfaces (glass and painted surfaces) of oven is
protected against external threats.
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
22
INJECTOR TABLE
LPG
NG
G20
G30
Gas Category: II2H3+
28-30 mbar
20 mbar
RAPID BURNER
Injector Diameter (%mm)
Nominal Rating (kW)
Consumption in 1h
115
85
2.75
3
218.1 gr/h
Consumption in 1h
285.7 lt/h
(at 150C and 1013mbar pressure)
SEMI-RAPID BURNER
Injector Diameter (%mm)
Nominal Rating (kW)
Consumption in 1h
97
65
1.75
1.75
127.2 gr/h
Consumption in 1h
166.7 lt/h
(at 150C and 1013mbar pressure)
AUXILLARY BURNER
Injector Diameter (%mm)
Nominal Rating (kW)
Consumption in 1h
72
1
50
1
72.7 gr/h
Consumption in 1h
95.2 lt/h
(at 150C and 1013mbar pressure)
OVEN BURNER
Injector Diameter (%mm)
Nominal Rating (kW)
Consumption in 1h
120
2.8
76
2.8
203.6 gr/h
Consumption in 1h
266.7 lt/h
(at 150C and 1013mbar pressure)
GRILL BURNER
Injector Diameter (%mm)
Nominal Rating (kW)
Consumption in 1h
110
2.2
68
2.2
160 gr/h
Consumption in 1h
209.5 lt/h
(at 150C and 1013mbar pressure)
For Customer Services, Spare parts & Warranty Information please call 0845 683 8717
23
For Customer Services, Spare Parts &
Warranty Information please call
0845 683 8717
Opening times:
Monday - Friday
8am until 8pm
Saturday & Sunday 10am until 4pm
Customer Service Department
Picktree Court
Picktree Lane
Chester-le-Street
Co Durham
DH3 3SY
Revision 1
This symbol is known as the 'Crossed-out wheelie bin Symbol'. When this
symbol is marked on a product/batteries, it means that the product/batteries
should not be disposed of with your general household waste. Only discard
electrical/electronic/battery items in separate collection schemes, which cater
for the recovery and recycling of materials contained within. Your co-operation
is vital to make sure the success of these schemes and for the protection of the
or ask in store for details.
We reserve the right due to possible changes to design to alter the instruction
manual without prior notice.
52037498 10/10 R000
|